Eradicating a camper awning generally is a daunting activity, but it surely would not need to be. With the correct instruments and slightly endurance, you’ll be able to take away your awning shortly and simply.
Earlier than you start, ensure you have all the mandatory instruments. You will want a ladder, a screwdriver, a wrench, and a pair of pliers. You might also wish to have a helper readily available to help you.
After you have gathered your instruments, start by eradicating the screws that maintain the awning arms to the camper. Subsequent, take away the bolts that maintain the awning curler to the camper. As soon as the bolts are eliminated, you’ll be able to rigorously raise the awning curler off the camper. Watch out to not injury the curler or the awning cloth.
Collect Essential Instruments and Supplies
To make sure a easy and environment friendly camper awning removing course of, it’s essential to collect the mandatory instruments and supplies beforehand. This is a complete record to information your preparation:
Instruments:
| Device | Goal |
|---|---|
| Adjustable Wrench or Socket Set | Loosening and tightening bolts and nuts |
| Phillips and Flathead Screwdriver Set | Eradicating screws that maintain awning elements in place |
| Utility Knife | Slicing awning cloth and cordage |
| Hammer | Tapping gently to launch caught elements |
| Pliers | Gripping and pulling cloth and cordage |
Supplies:
| Materials | Goal |
|---|---|
| Awning Material Cleaner | Cleansing awning cloth earlier than storage |
| UV Protectant Spray | Defending awning cloth from solar injury throughout storage |
| Awning Storage Case | Storing awning cloth and elements neatly and securely |
Retract and Safe the Awning
Comply with these steps to retract and safe the awning as a part of the removing course of:
1. Retract the Awning
a. Ensure the awning arms are straight, parallel to the camper, and never angled outwards or inwards.
b. Slowly use the pull strap or swap to retract the awning.
c. Guarantee the material has rolled up evenly on the curler tube.
d. When totally retracted, safe it with a strap or bungee wire.
2. Safe the Awning
a. Examine the awning cloth for any tears, holes, or free seams. Restore any injury earlier than securing.
b. Fold the aspect flaps of the awning cloth towards the curler tube, defending the material from flapping within the wind.
c. Wrap the tip flaps of the awning cloth across the curler tube, overlapping them barely to maintain moisture out.
d. Safe the awning cloth to the curler tube utilizing Velcro straps or a wrap-around cowl.
e. Tighten any free bolts, nuts, or screws that maintain the awning in place.
3. Clear the Awning
a. Use a delicate fabric or sponge and a gentle cleaning soap answer to wipe down the awning cloth.
b. Rinse totally with clear water and permit to dry.
c. Apply a UV protectant spray to assist forestall fading and injury from the solar.
| Instruments and Supplies Wanted |
|---|
|
|
By following these steps, you’ll be able to retract and safe the camper awning correctly to guard it from injury throughout storage or transportation.
Take away the Truss Arms
The truss arms are the steel rods that reach from the awning curler to the highest of the awning. They help the load of the awning and hold it from sagging.
To take away the truss arms, you’ll need to:
- Find the truss arm mounting brackets on the aspect of the RV.
- Loosen the bolts that maintain the mounting brackets in place.
- Take away the truss arms from the mounting brackets.
- Repeat steps 1-3 for the opposite truss arm.
Suggestions for Eradicating the Truss Arms
* Watch out to not injury the awning cloth if you find yourself eradicating the truss arms.
* If the bolts are rusted or caught, you need to use a penetrating oil to loosen them.
* If you’re having issue eradicating the truss arms, you’ll be able to contact a certified RV technician for help.
WARNING: Earlier than eradicating the truss arms, ensure that the awning is totally retracted. Failure to take action may end in severe damage or injury to the awning.
| Instruments Wanted |
|---|
| Socket wrench |
| Screwdriver |
| Penetrating oil (non-compulsory) |
Take away the Awning Curler
Eradicating the awning curler includes a couple of further steps:
- Help the awning cloth: Loosen the material stress by winding within the awning about midway. It will cut back the load on the curler.
- Disconnect the facility: If the awning is motorized, disconnect the facility supply on the electrical panel or circuit breaker.
- Take away the tip caps: On both sides of the curler, you may discover finish caps that safe the material and curler. Take away these caps utilizing a screwdriver or wrench.
- Slide out the curler: With the tip caps eliminated, now you can slide the curler out of the awning tube. Watch out to not injury the material or curler as you accomplish that.
| Step | Motion |
|---|---|
| 1 | Loosen the material stress |
| 2 | Disconnect the facility (if motorized) |
| 3 | Take away the tip caps |
| 4 | Slide out the curler |
Detach the Awning Material
Now that the awning arms are indifferent, you’ll be able to take away the awning cloth. Begin by unhooking the material from the curler tube. There are often a number of hooks or clips that maintain the material in place. As soon as the material is unhooked, rigorously roll it up and safe it with a strap or bungee wire.
Eradicating the Awning Material
| Step | Motion |
|---|---|
| 1 | Unhook the material from the curler tube. |
| 2 | Rigorously roll up the material. |
| 3 | Safe the material with a strap or bungee wire. |
Take away the Fascia and Drip Rail
The fascia is the vertical trim piece that runs alongside the highest of the awning. It’s usually held in place by screws or bolts. The drip rail is the smaller trim piece that runs alongside the underside of the fascia. It’s usually held in place by screws or adhesive tape.
To take away the fascia and drip rail, comply with these steps:
- Find the screws or bolts that maintain the fascia in place. These are usually positioned alongside the highest fringe of the fascia.
- Take away the screws or bolts.
- Gently pry the fascia away from the RV. It might be useful to make use of a putty knife or different skinny object to assist pry the fascia free.
- As soon as the fascia is eliminated, you’ll be able to take away the drip rail. The drip rail is often held in place by screws or adhesive tape.
- If the drip rail is held in place by screws, take away the screws.
- If the drip rail is held in place by adhesive tape, use a warmth gun or hair dryer to warmth the tape till it turns into delicate. As soon as the tape is delicate, you’ll be able to gently pry the drip rail away from the RV.
| Screw or Bolt Dimension | Amount | Location |
|---|---|---|
| 1/4″ x 1″ | 4 | High fringe of fascia |
| #8 x 1-1/2″ | 6 | Backside fringe of drip rail |
Seal the Opening
As soon as the awning is eliminated, the opening within the RV wall must be sealed to forestall water and pests from getting into. This may be executed with a wide range of supplies, together with silicone caulk, butyl tape, or a mixture of each.
Supplies Wanted:
| Materials | Goal |
|---|---|
| Silicone caulk | Seals gaps and cracks |
| Butyl tape | Creates a weather-tight barrier |
| Caulk gun | Dispenses caulk |
| Butyl tape curler | Applies butyl tape evenly |
Steps:
1. Clear the opening across the perimeter of the awning tube.
2. Apply a bead of silicone caulk across the opening.
3. Roll out a strip of butyl tape over the caulk, guaranteeing it overlaps the caulk by not less than 1 inch on both sides.
4. Use a caulk gun to use a second bead of silicone caulk over the butyl tape.
5. Clean out the caulk utilizing a finger or a caulk ending device.
6. Enable the caulk to treatment in response to the producer’s directions.
7. Double-check the seal for any gaps or cracks, and apply further caulk or butyl tape as wanted.
Examine and Clear the Eliminated Parts
Examine the Material
Unfold the awning cloth and examine it totally for any injury, similar to tears, holes, or stains. When you discover any injury, mark it with a bit of tape or chalk so you’ll be able to restore it later.
Clear the Material
Use a gentle cleaning soap answer and a delicate brush to scrub the material. Keep away from utilizing harsh detergents or bleach, as these can injury the fabric. Rinse the material totally with clear water and permit it to air dry.
Examine the Body
Examine the awning body for any indicators of injury, similar to rust, corrosion, or bending. When you discover any injury, it is very important restore it earlier than reassembling the awning.
Clear the Body
Use a gentle cleaning soap answer and a delicate brush to scrub the body. Pay particular consideration to the areas the place the material attaches to the body, as these areas usually tend to accumulate dust and particles. Rinse the body totally with clear water and permit it to air dry.
Examine the Arms and Brackets
Examine the awning arms and brackets for any indicators of injury, similar to bent or damaged elements. When you discover any injury, it is very important change the affected elements earlier than reassembling the awning.
Clear the Arms and Brackets
Use a gentle cleaning soap answer and a delicate brush to scrub the arms and brackets. Pay particular consideration to the areas the place the arms connect to the body and the brackets connect to the RV, as these areas usually tend to accumulate dust and particles. Rinse the arms and brackets totally with clear water and permit them to air dry.
Examine the Drive Motor
In case your awning is provided with a drive motor, examine the motor for any indicators of injury, similar to free connections or defective wiring. When you discover any injury, it is very important restore or change the motor earlier than reassembling the awning.
Clear the Drive Motor
Use a delicate fabric to scrub the outside of the drive motor. Keep away from utilizing water or another liquids, as these can injury the motor. If the motor is especially soiled, you need to use a vacuum cleaner to take away any free dust and particles.
Lubricate Transferring Elements
Common lubrication is essential for sustaining the sleek operation of your camper awning. Making use of lubricant to the shifting elements helps cut back friction and prevents untimely put on or injury. This is an in depth information to lubricating the shifting elements of your camper awning:
Instruments and Supplies
| Merchandise | Amount |
|---|---|
| Silicone-based lubricant spray | 1 can |
| Clear fabric | 1 |
Steps
-
Clear the shifting elements: Begin by cleansing the awning’s arms, joints, and pulleys with a humid fabric to take away any dust or particles which will have collected. Enable the elements to dry fully earlier than lubricating.
-
Establish the lubrication factors: Find the shifting joints the place friction is prone to happen, such because the hinge factors of the awning arms and the pulleys that information the awning cloth.
-
Apply lubricant: Shake the lubricant can totally earlier than use. Spray a light-weight coat of lubricant onto every lubrication level, guaranteeing the lubricant penetrates the joints and pulleys. Keep away from over-lubricating, as this may entice dust and particles.
-
Wipe away extra: Use a clear fabric to wipe away any extra lubricant which will have dripped or leaked out. This helps forestall dust from sticking to the lubricated elements.
-
Lubricate commonly: Repeat the lubrication course of each few months or extra steadily in case your awning is used steadily or uncovered to harsh climate circumstances. Common lubrication will delay the lifetime of your awning and hold it working easily.
Reinstall the Awning
To reinstall the awning, merely reverse the removing steps.
.
1. Insert the alternative finish of the awning into the curler tube.
2. Roll up the awning and safe it with the strap or wire.
3. Align the awning tube with the mounting brackets and slide it into place.
4. Tighten the bolts or screws to safe the awning.
5. Connect the help arms to the awning tube and lengthen them outwards.
6. Alter the help arms to stage the awning.
7. Connect the tip caps to the awning tube.
8. Join the awning cloth to the help arms and safe it with the material clamps.
9. Roll out the awning and lengthen it to its desired size.
10. Lengthen the awning legs to help the awning and modify the peak as wanted.
| Bolt/Screw Dimension | Tightening Torque |
|---|---|
| 1/4″ | 10-15 ft-lbs |
| 5/16″ | 15-20 ft-lbs |
| 3/8″ | 20-25 ft-lbs |
| 1/2″ | 25-30 ft-lbs |
How To Take away Camper Awning
Eradicating a camper awning generally is a daunting activity, but it surely’s truly fairly easy in case you comply with the steps under. First, you may want to collect your instruments. You will want a ladder, a socket wrench or drill, and a helper.
After you have your instruments, you can begin eradicating the awning. First, climb up the ladder and unhook the awning from the curler tube. Watch out to not drop the awning, as it may be heavy.
Subsequent, take away the bolts that maintain the curler tube to the camper. Be sure you help the curler tube as you take away the bolts, as it may be heavy.
As soon as the curler tube is eliminated, you’ll be able to take away the awning cloth. Begin by unhooking the material from the curler tube. Then, fold up the material and retailer it in a secure place.
Lastly, you’ll be able to take away the awning arms. Begin by eradicating the bolts that maintain the arms to the camper. Then, rigorously take away the arms. Watch out to not injury the camper as you take away the arms.
Individuals Additionally Ask About How To Take away Camper Awning
How do you take away a slide out awning?
To take away a slide out awning, you may must comply with the steps under:
1. Retract the awning all the best way into the housing.
2. Unbolt the mounting brackets from the slide out.
3. Rigorously raise the awning straight up and off of the mounting brackets.
4. Retailer the awning in a secure place.
How do you take away a retractable awning?
To take away a retractable awning, you may must comply with the steps under:
1. Retract the awning all the best way into the housing.
2. Take away the screws that maintain the housing to the wall.
3. Rigorously raise the housing straight up and off of the wall.
4. Disconnect {the electrical} wires from the motor.
5. Retailer the awning in a secure place.
How do you take away a window awning?
To take away a window awning, you may must comply with the steps under:
1. Take away the screws that maintain the awning to the window body.
2. Rigorously raise the awning straight up and off of the window body.
3. Retailer the awning in a secure place.
